Refinishing Hardwood Floors – Sanding
Refinishing a hardwood floor is an straightforward technique to add beauty and worth to any home. It may also be a real ego increase for the do it yourselfer. Performing it oneself will save you money in the event you follow these straightforward methods. Get a lot more information about golvslipningstockholms.nu
One of the most critical element to consider when refinishing is really a hardwood floor is cleanliness. You desire to be sure the floor is free from any debris. Debris can get caught within the sander and damage the floor. Modest jagged stones will be the most damaging. At times it is not achievable to see the damage until after you apply your finish coats, after which it’s too late.
The baseboards are also an additional element you need to take into consideration. For those who are confident with your capabilities, you can gently remove them having a modest flat-bar as well as a hammer. Take your time. The idea is usually to remove and replace, not get rid of then drive for the hardware store for the reason that you broke the boards. You’ll be able to leave the baseboards in place if it isn’t practical to eliminate them. If you opt for to leave the baseboards, I advocate that you simply defend them with painters tape. The power sander will damage them for those who are usually not careful.
When the floor is clean, and also the baseboards have been removed or protected sufficiently, you are able to commence to sand. I propose renting an orbital sander with a rectangular face. (Be cautious when transporting it to and from your home and ensure you have someone help when lifting the sander.) Start out with 80 grit sand paper. Guide the sander smoothly over the floor. Make sure you are sanding parallel together with the joints in the floor. Attempt to not sand perpendicular towards the joints, as this kind of sanding can damage the wood and lead to the finish to look less than fantastic. The number of passes it requires to get rid of the old finish will differ from floor to floor. Be deliberate. Get rid of all the old finish just before you move to a smaller girt sand paper.
Now that you are completed sanding using the 80 grit sand paper, you can need to sweep or vacuum the floor. This removes any massive wood particles or debris that might have been dislodged. After cleaned, sand the floor in specifically the same fashion using 120 grit sand paper. You are going to notice the 120 grit sand paper sands extremely effectively. This really is mainly because that you are no longer sanding via the old finish plus the sand paper is straight around the face of the wood. Endeavor to be smooth and fluid as you move the sander. If you pause or stop, you’ll over sand and develop low spots in the floor.
You may know when the sanding is full by the look and really feel on the floor. Visually you are going to not see any shinny or glossy locations. The floor will have a smooth and dry really feel to it. Take you time for you to crawl about and closely inspect the floor. If you uncover any places that usually do not meet your standards, meticulously sand them once more. As you sand more than the imperfections, be sure that you do not hold the sander in one location to get a prolonged time frame. Instead, make passes over the location needing to be sanded; quick ones very first, followed by progressively longer ones. This approach is named feathering and will help protect against over sanding your floor in any one area.
After your final inspection of the floor is total, you might need to clean once again. Deliberately vacuum or sweep up each of the debris. Then, using a slightly damp cotton towel, wipe more than the entire floor surface. When you are wiping, maintain the towel in one orientation against the floor. Do not pick it up. The aim is usually to capture any compact debris left behind on the front face in the towel. You are going to notice that the floor wicks several of the water out on the towel. That is normal and can not impact your final finish as long as you permit it to dry.
In conclusion, refinishing a hardwood floor doesn’t have to be complicated. Keep in mind to clean the floor before you get started to sand. Clean the floor whenever you adjust the girt size with the sand paper you are using. When comprehensive, you will have a smooth floor ready to accept its first coat of finish.
0
0
