How Industrial Air Conditioning Brazing Works
Brazing is characterized as combining two parts at a temperature of more than 800 degrees Fahrenheit. The temperature edge should be met for the brazing to be effective.
The holding material used to join cooling parts is known as sil-phos. The higher the substance of silver in the sil-phos the higher the nature of the compound.
Six Steps for Air Conditioning Brazing Works
The Industrial Air Conditioning Industry has set up 6 fundamental strides to braze cooling parts effectively. These means follow a particular request to finish the cycle.
Itently, follow these six Industrial Air Conditioning Brazing Work steps to braze Industrial cooling parts together:
1. Basic Fit with Proper Clearance
Brazing cooling parts together requires the parts to fit appropriately giving the legitimate freedom before the parts are for all time joined. In the event that the freedom isn’t the appropriate distance and the parts don’t fit definitely once joined the work gets muddled Aircon servicing.
The ideal freedom range for two sections to be joined are between .001-.003 and not more prominent than .005. Assuming two sections Aircon installation fall inside the ideal reach, the entire Brazing Air Conditioning Brazing Works measure streams easily.
Additionally, if the freedom is under .001 the liquid filling material won’t move through the joint. On the off chance that the freedom is more prominent than .005, or .006 the filling compound may not fill the joint totally. There is an almost negligible aircon chemical overhaul difference to accomplish the appropriate freedom between the two joined parts.
Fitting
The following piece of the progression is to build up the appropriate fitting of the cylinders together in the brazing interaction. Aircon chemical wash On the off chance that the cylinders fit are copper to copper, the warmth development of the two separate copper openings will be equivalent.
The cylinders are copper to tempered steel, for instance, at that point the development warming rates will be extraordinary. To tackle Aircon repair a potential rebel chime between the two cylinders follows these rules:
On the off chance that the warming cycle will decrease the freedom between the two cylinders (due to various materials being joined) at that point take into account a free leeway of .010. In the event that the warming causes extending the leeway between the cylinders, consider more tight freedom before the parts are warmed Aircon gas topup.
2. Clean the Metals
For the filling to hold fast to two combining surfaces they should be spotless and liberated from every single unfamiliar substance. The surfaces have oil, oil, or soil on them the filler won’t tie the two sections together. Clean sleek or oily surfaces with a dissolvable, if the surfaces are oxidized clean them with an emery fabric. Consolidate the two Daikin aircon servicing urfaces following cleaning them. Why? Defer the joining of two surfaces and they will become sullied once more.
3. Motion the Parts
Motion, a synthetic compound, will be either a fluid or glue. It is applied to a joint surface prior to brazing happens. Transition will shield surfaces from oxidizing and the motion will absorb any oxides and it will assist the compound with streaming appropriately Mitsubishi aircon servicing.
Transition doesn’t generally need to be applied prior to brazing. On the off chance that the two surfaces are copper to copper, transition isn’t required. In any case, a phosphorous filler should be utilized all things being equal. Assuming the two surfaces are of various arrangement (copper to steel) transition should be applied.
Motion might be applied by brush or applied straightforwardly into the filler material with a motion pole or motion covered wire.
4. Set up for Brazing
This is a basic advance in the Industrial Air Conditioning Brazing Works measure. The real warming and brazing measure is impossible without this progression. The two sections should be arranged and upheld for appropriate brazing to occur.
Mechanical cooling parts are intended to adjust and uphold once embedded together. The parts brazed together are rounded formed. Amass the two sections by completely setting one section inside the other part for legitimate fixing and interfacing in the brazing cycle.
5. Complete the Brazing Process
Warmth the two sections uniformly to cover the two surfaces. The filler metal should be wet proportionately on both part surfaces. The best warming apparatus to utilize is a gas light. When the two sections have arrived at the appropriate warming temperature presently apply the filler joint material.
+65 83594701
Sugei kadut,
Singapore.