Can I Install Vinyl In Bathroom?
Not only do bathrooms and other damp spaces like laundry suffer from frequent wear and tear and high foot traffic, but they are also exposed to wetness all the time. Bathroom floors therefore need to be waterproof, robust, and simple to clean. If you want to buy Waterproof bathroom flooring, Patterned vinyl, Flooring for hallway, etc, visit Vinyl Flooring UK.
- Waterproof:
Vinyl flooring for bathrooms is completely waterproof, so spills and moisture won’t harm your floors. This is so that you can stop worrying about boards swelling or warping because the material does not absorb moisture by nature. Vinyl flooring is a great addition to the kitchen in addition to the bathrooms and laundry area.
- Slip-resistant:
Because they are all non-slip, vinyl planks are a great option for bathrooms. This naturally translates into improved foot grip, particularly following a shower or bath.
- Comfy underfoot:
Vinyl bathroom flooring is a robust flooring material that tends to absorb ambient heat in the room more effectively than ceramic tiles. Vinyl doesn’t freeze in the winter because of this. This makes walking barefoot on the floor more comfortable and gentler. Are you in need of greater comfort? It may surprise you to learn that vinyl planks work well with underfloor heating.
How to Install Vinyl Flooring in Your Bathroom
Things You’ll Need: A vinyl cutter, Double-sided tape, Bathroom silicone sealant, T-bar for doorway join, A beautiful sheet of vinyl floor, A sharp utility knife, Sprat-adhesive, Edging(optional)
Take Safety Measures:
-Note that the instruments are sharp and may cut you. When handling blades, take care to cover them when not in use. Gloves should be used when working with silicone.
-Make sure to read carefully and follow the safety instructions listed on the product.
-Wearing knee pads will protect your knees, thus it’s a smart idea.
Preparation:
Most floors are ideal for covering with vinyl sheets. If you’re not sure if you should strip the old floors before buying your vinyl sheet, contact professionals.
If necessary, use the proper product or solvent to strip flooring. It is necessary to hoover and sweep the current floor. To guarantee a smooth and flush floor, any nails or screws that protrude below the surface must be pounded out. Dust and trash must be removed from the floor. Concrete floors need to be completely dry. There is an easy way to check for moisture:
-Cut a 1-square-meter-sized piece of polythene plastic.
-Seal the edge with insulating tape and place it on the floor.
-Leave overnight.
-The following day, if there is still any water on the polythene, it indicates that there is moisture. Before installing the new bathroom flooring, get rid of it.
-In order to achieve a superior finish, we advise levelling the floor if it is currently damaged or uneven.
Measure Your Bathroom Floors:
It’s critical to take precise measurements and confirm that the right size sheet is available without requiring needless connections. Measure the length, width, and any nooks and crannies of the space. Take a measurement up to the entrance’s centre. To allow for final trimming and cutting, add 75 cm to each edge. You can now purchase the bathroom vinyl sheets using the measurements.
Installing Vinyl Flooring in Bathrooms:
For relaxation, roll out the vinyl sheet in the bathroom and keep it there for a full day. Turn off your underfloor heating system at least 24 hours before applying vinyl.
Gently place the vinyl in the desired location, allowing the 75mm extra to overlap, then adjust to fit as closely as possible. Cuts must be made around obstructions such as a pedestal washbasin or toilet. Using your utility knife, make a number of incisions in the vinyl surrounding the pedestal and toilet:
- To begin, make a slit in the centre where the vinyl meets the pedestal (or toilet) and cut it all the way to the edge. Cut upward into the area that will be cut away.
- Press down on the vinyl that has been fitted around the pedestal on both sides of the pedestal, then cut at regular intervals at an angle towards the initial cut, cutting from the edge upward into the surplus.
- Press the vinyl firmly into position and press the just-formed flaps up against the pedestal. The pedestal’s rear flaps need to fit together perfectly.
- Trim the extra vinyl so that the opposite end fits perfectly underneath the pedestal.
- Keep going around the pedestal, trimming off any extra flaps.
- Work around the edges to tidy up after overcoming all the challenges.
- To achieve a beautiful straight edge, the edges then need to be cut with a vinyl cutter, giving a long, straight cut. When working in a bathroom, in particular, try to avoid making any incisions in damp places as water can seep underneath and harm the vinyl.
It is necessary to adhere all sheet vinyl flooring to the floor:
Occasionally, an adhesive that is applied to the entire floor or sheet of vinyl is required to fully bind the sheet to the floor. Other materials merely require double-sided vinyl floor tape to be glued at joints and around the perimeter. Note that glue is required for the entire surface when using non-cushion vinyl sheets.
Prior to using double-sided tape, ensure that the floor is spotless, level, and devoid of any pores. The area where the double-sided tape is placed needs to be sprayed with adhesive if the floors aren’t spotless, smooth, and non-porous.
If you’re using adhesive, carefully avoid spraying onto the walls by only using it at the floor’s edge. Next, without removing the backing paper, adhere the double-sided tape to the adhesive along the sides of the room. The tape can be securely smoothed in place by running a slab of wood over it. Apply the same care to any other obstacles and the pedestal’s base.
At last, the sheet vinyl may be positioned and fixed into position. Lift each edge as you proceed around the edge. Press the sheet vinyl firmly onto the double-sided tape after removing the backing.
